MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE GSD4000DWW
White GE GSD4000DWW has an eleven-touchpad electronic front panel, five cycles, a CLEAN light and a middle wash tower. Its own GSD4000-only table identifies beeping CLEAN or NORMAL WASH flashes as Control Error.
The actual GSD4000DWW control panel
GSD4000DWW is the white, twenty-four-inch built-in GE dishwasher whose exact product listing specifies an electronic front panel with eleven touchpads. A CLEAN cycle-progress indicator, START/RESET, last-cycle memory and a control lock are part of this SKU, not guesses from a generic standard-tub booklet. The linked manual's page eight illustrates several possible panels; the bottom electronic panel has CLEAN, NORMAL WASH and START/RESET in the positions needed to read its later flashing-light table. Page ten narrows that section to model GSD4000 only. The full DWW sales suffix is absent from the PDF, but the manufacturer's exact product-to-manual link and matching control specification support this application. This scope matters because a dial-controlled dishwasher shown higher on page eight cannot display the same electronic lamp pattern. The product data also names a plastic tub, twelve place settings and a 60-decibel quiet package, useful identifiers before asking about a signal.
Cycle choices and dish-loading geometry
Five wash cycles are listed for the exact machine, among them Pots & Pans, Heavy Wash, Normal Wash, China/Crystal and Rinse Only. The manual's electronic cycle chart gives Normal Wash 4.0 gallons over 120 minutes and Pots & Pans 8.8 gallons over 112 minutes; these numbers describe the listed program table, not a promise for every installation. Rinse Only is for a partial load to be cleaned later and takes no detergent. A two-, four- or eight-hour delay, heated drying and higher-temperature options change when the user expects the run to finish. Last-cycle memory can light a previous selection when the door latches, so an old option may appear without a new keypress. The lower rack needs a clear middle channel because a tower rises through it while washing. GE also lists a Piranha hard-food disposer and two-stage self-cleaning filtration with an extra-fine filter. Large pans or handles must not block that water path.
Read each flashing lamp with its sound
The diagnostic chart distinguishes a normal reset from two control errors. START/RESET flashing after the pad was pressed means the dishwasher is draining and resetting; wait before starting another load. CLEAN flashing together with a beeping sound is identified as Control Error. Press START/RESET to stop the beeper, and request service if CLEAN keeps blinking. A flashing NORMAL WASH lamp with beeping is also called Control Error, but its sequence differs: press START/RESET, let the unit reset, then restart. If it persists, switch power off at the breaker for thirty seconds, retry and call service if the warning remains. These are indicator patterns with audible context, not numeric F codes. A door left open during a cycle produces a beep every thirty seconds until latched, which should be checked before assigning any noise to the lamp table. Note the exact illuminated pad and whether it blinks.
Water temperature and drainage checks
Cleaning complaints can have causes unrelated to either control pattern. The manual sets entering water between 120 and 150 degrees Fahrenheit; water below the lower bound can leave detergent and food behind. The upper rack takes cups and glasses, while plates and cookware belong below with dirty sides facing the center. A dish at the front right can obstruct detergent circulation, and an item protruding through the lower rack can stop the spray arm. When water will not pump out, the care chapter advises checking an installed air gap; a sink or disposer drain can also be involved. Conversely, a little clean water around the rear bottom outlet lubricates the seal and is normal. These observations should be reported separately from CLEAN or NORMAL WASH flashing with a beep. State cycle, options, lamp, sound, door position and whether the tub actually drained before making a repair decision.
Verified model details
The PDF explicitly restricts the diagnostic table to GSD4000, matching the exact SKU.
Source for this detailNormal START/RESET flashing after cancellation means draining and reset.
Source for this detail · Source page: 8Two-stage filtration, Piranha disposer and rising tower shape loading advice.
Source for this detail · Source page: 10
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE® Built-In Dishwasher - GSD4000DWW - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.