Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE JT910WAWW
GE JT910WAWW is a white 30-inch single wall oven. Its linked GE manual covers the JT910 family and documents an F-pattern fault, Probe reminder, control lock and self-clean door alerts.
Confirm the single-oven model
JT910WAWW is GE's White on White, 30-inch single wall oven. The GE listing gives overall dimensions of 28 1/4 inches high by 30 inches wide by 23 1/2 inches deep, SmartSet controls, convection cooking and three racks. This is one cooking cavity, so the drawing of a double-oven panel in the family booklet must not be treated as the layout of this appliance. The PDF cover explicitly includes JT910, alongside related JKP and JTP models; its troubleshooting guidance therefore has a documented family connection. If the suffix on your appliance is uncertain, the manual says the model and serial label for a single oven is at the front behind its door. Confirm that label before using parts diagrams or a different variant's instructions.
Handle an F-pattern error in order
A flashing F followed by a number or letter is the function error pattern in the linked GE troubleshooting table. The owner manual does not decode particular F numbers or letters, so a web claim that a given suffix proves a bad board or sensor would exceed this source. Note the full display and what the oven was doing. GE's first step is CLEAR/OFF and one hour of cooling before putting the oven back into operation. If the function code repeats, disconnect all power to the oven for at least 30 seconds, then restore it. A further recurrence is the point at which the manual directs you to service. A flashing clock after a power failure belongs to a different row: reset the clock and any interrupted cooking program before deciding an F fault remains.
Interpret nonfault display messages
Several messages on JT910WAWW can be useful prompts rather than faults. GE's exact specification includes an automatic meat thermometer probe; the family chart explains that Probe appears after connection when the control needs a target probe temperature. A dark display can reflect a tripped household breaker, blown fuse or the optional clock blackout setting. If power has returned and the clock flashes, reset the time and cooking function. GE also confirms control lock capability for this SKU. In the manual's special-feature instructions, pressing a locked touchpad produces LOC; the clock, kitchen timer and oven-light pads remain available. The kitchen timer merely counts time and does not switch oven heat on or off. These checks help separate an expected setting from the F-pattern diagnostic before requesting a repair.
Understand self-clean door messages
The GE product data calls JT910WAWW self-cleaning and specifies an automatic door lock. LOCK DOOR flashing when you choose self-clean means the door was not closed; close the oven door as GE directs. Once a clean cycle is running, the lock serves a different purpose: the door cannot open until the cavity has cooled and the LOCKED DOOR light goes out. Do not force it when hot. Before a cycle, GE instructs removal of the broiler pan, grid, temperature probe, cookware and foil, and wiping heavy soil. A locked door after cleaning may simply need more cooling time; an F-pattern flash uses the separate fault sequence above. This distinction prevents treating normal protective locking as the same event as a function error.
Use this oven's cooking features as intended
This particular single oven has convection bake and roast capability, seven rack positions and GE-listed Proof Mode. The manual's 30-inch guidance explains that shelf position affects baking, and its family troubleshooting table lists a missing removable oven floor as a possible cause of poor results where that part is fitted. Check the actual oven configuration before applying that row or changing a thermostat setting. The cooling fan can continue after the oven is turned off, and visible steam at the vent during convection is described as normal. Proof mode displays BRD while it gives dough a warm rising environment; GE warns that it is not a food-holding setting. Broiling also will not start with the meat probe still plugged in. Read each behavior alongside the selected mode rather than automatically calling it a failure.
Verified model details
The exact GE listing confirms the single-oven configuration; the linked manual cover names JT910.
Source for this detail · Source page: 1The documented fault is an F followed by a number or letter, with a defined reset and service sequence.
Source for this detail · Source page: 32LOCK DOOR, LOC and Probe are separate messages with different user actions.
Source for this detail · Source page: 31
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE Profile Performance™ 30" Single Wall Oven - JT910WAWW - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.