Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE JK915WFWW
GE JK915WFWW is a white 27-inch single convection wall oven. Its linked GE manual documents an F-pattern error and separate lock, door and probe messages.
Identify the 27-inch oven
JK915WFWW is the White on White, 27-inch single wall oven in GE's Profile convection line. The exact product record gives a 3.90-cubic-foot cavity, three heavy-duty racks, four rack positions and an overall width of 26 5/8 inches. The linked manual cover names the JK915 family as a 27-inch single oven, but it also covers double ovens and shows a double-oven control drawing on page 5. Use the model and serial label on the side trim or behind the door to confirm your unit before following a diagram. The four-position guidance for 27-inch ovens is more relevant here than the seven-position guidance for 30-inch versions.
Read an F-pattern fault
If the display flashes F followed by a number or letter, the GE troubleshooting table calls it a function error code. The manual does not assign individual F suffixes to particular failed parts, so writing down the entire displayed pattern is more useful than guessing at a sensor or board. GE's first action is CLEAR/OFF, then a full hour for the oven to cool before retrying. If the same pattern returns, disconnect all power for at least 30 seconds and reconnect it. A code that appears again after that sequence is the point at which the manual directs you to service; repeated resets are not a repair.
Separate lockout from a blank display
LOC ON is the control lockout indication, not the F-pattern failure. On this single oven, the manual says to hold the 9 and 0 number pads together for three seconds; LOC OFF confirms that the touch controls have been released. Separately, the kitchen timer counts down without operating the oven, so check the chosen cooking mode as well as any timer setting. A completely dark display raises a different question. GE lists both a household fuse or tripped circuit breaker and the optional clock black-out mode as possible explanations. Check the household supply and clock setting before treating that blank screen as a function code.
Understand the cleaning-door message
The troubleshooting table calls an open-door self-clean prompt LOCK DOOR, while the operating instructions say LOCKED can flash for the same condition. Close the door to address that prompt. A lit LOCKED DOOR signal is separate: the door remains locked because the oven has not cooled below its release temperature; allow cooling rather than forcing the handle. JK915WFWW's exact product specification lists an automatic self-clean door lock, which fits these manual explanations. Before a cleaning cycle, remove the broiler pan, grid, temperature probe, cookware and aluminum foil as GE instructs. These steps matter because a door message, a hot cavity and an F error require different responses even though each interrupts the task you were trying to start.
Use the probe and proof indicators
The exact JK915WFWW specification includes a temperature probe. When Probe appears after the probe is plugged in, the control is asking for a target food temperature; enter that temperature rather than interpreting the word as a fault. Proofing has its own indicators. The GE instructions say PrF appears while proof mode is active, whereas HOT appears if the cavity is above 125°F and proofing cannot begin. Wait for the oven to cool before trying that mode again. Proof mode is intended for rising dough, not for holding cooked food safely hot. Keeping those display states separate prevents needless service calls and makes it easier to describe a real fault accurately.
Check convection behavior and racks
For this model GE lists True European Convection with Precise Air, and the manual explains that the convection fan stops when the door is opened. That pause is expected behavior. For a 27-inch convection roast, the instructions specify the offset rack in the low A position; take care when reaching for a rack so near the door. On the troubleshooting page, steam at the vent during convection cooking is also treated as normal. After switch-off, the cooling fan on a 27-inch version may continue for up to two hours to cool internal parts. A fan noise or a little vent steam therefore needs context, while a recurring F-pattern after GE's reset sequence needs service.
Verified model details
The exact GE model listing and JK915 manual cover establish a single 27-inch oven.
Source for this detail · Source page: 1The documented fault is an F followed by a number or letter, with a staged reset procedure.
Source for this detail · Source page: 28LOC ON, LOCK DOOR and Probe describe three different conditions.
Source for this detail · Source page: 27
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE Profile™ 27" Built-In Single Convection Wall Oven - JK915WFWW - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.