MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE GSD5200GBB
GSD5200GBB is a black, 24-inch GE built-in dishwasher with five cycles and a GSD5200-specific China/Crystal setting. Its linked manual shows three different flashing-light situations, including two beeping Control Error patterns.
Identify this GSD5200 variant
GE identifies GSD5200GBB as the black member of its built-in GSD5200 dishwasher line. The exact product listing gives a 24-inch overall width, electronic controls, eleven touchpads and five cycles. Its linked owner's manual names both GSD5200 and GSD5300, so the family cover alone is not enough to distinguish them. The GSD5200 panel drawing and the exact product record are the stronger guides for this particular suffix, especially when comparing a replacement machine.
This version has a Clean progress light, Last Cycle Memory and Control Lock. GE also lists a Piranha hard-food disposer and self-cleaning triple filtration for GSD5200GBB. Those are features of the exact listing, not assumptions taken from every GSD manual illustration. A reader checking a fault should first locate the Clean light on the real control panel; a different panel can turn a seemingly familiar blinking pattern into the wrong diagnosis. The black finish and filtration details help confirm that the product page is for the intended model.
Read the GSD5200 cycle chart
The manual's cycle chart has a separate GSD5200 row. China Crystal uses 8.2 gallons and is shown as 36 minutes, whereas Normal Wash is 9.9 gallons and 58 minutes. Rinse Only is 1.6 gallons and four minutes in that chart. These are programmed chart figures, not a promise that a household's water pressure or selected options will produce exactly those values. The GSD5200 panel drawing has Delay Start choices of two, four and eight hours; the neighboring GSD5300 drawing differs, which is why the row label matters.
China Crystal is intended for lightly soiled delicate ware; the ordinary Normal choice is for everyday dishes with medium soil. Heated Dry On adds about 30 minutes and cannot be selected with Rinse Only. The controls remember the last cycle, while a power interruption defaults to Normal and Heated Dry according to the manual. Start/Reset cancels an active program, drains water and takes roughly 90 seconds before a new selection can begin. A steady Clean lamp after completion remains lit until the door opens, so it should be read separately from a flashing warning.
Separate reset from a control fault
The illustrated table on page six treats a blinking Start/Reset pad after that pad was pressed as normal. Let the machine finish draining and resetting before attempting another program. This matches the approximately 90-second cancellation sequence on the control-settings page. A finished wash has another ordinary state: Clean glows steadily until the door is opened. Observing which lamp is blinking and whether a beeper sounds is more informative than calling every illuminated light an error code; this manual uses named light patterns rather than an alphanumeric display code here.
Two combinations in the same table are labelled Control Error. Clean flashing together with beeps calls for pressing Start/Reset to stop the sound, then service if Clean keeps flashing. Normal flashing with beeps has a different follow-up: Start/Reset lets the dishwasher attempt a reset, after which GE says to restart the wash; seek service if the error continues. Keep those two rows distinct when explaining a symptom. The page does not say a normal Start/Reset blink requires service, and it does not assign the Normal-row restart procedure to a persistently flashing Clean light.
Check water, loading and drainage
For weak cleaning, the linked manual first specifies incoming water between 120 and 150 degrees Fahrenheit. It also says Rinse Only does not need detergent in the main dispenser. On the racks, leave the lower center clear because the wash tower rises there to feed the middle spray arm; large items should not obstruct it. These details matter for GSD5200GBB because a poorly rinsed upper rack can result from loading or temperature before any electronic warning appears. They are useful checks to record separately from the light pattern.
If water is not draining well and the installation has an air gap, the care page recommends checking that fitting for debris. The air gap is plumbing equipment rather than a dishwasher part, so its presence depends on the installation. GE's exact listing also gives this model triple filtration and a hard-food disposer, which make the wash path worth keeping clear according to the relevant care instructions. Use Control Lock only as a control setting; do not confuse locked pads with the beeping Clean or Normal fault patterns. Persistent flashing after the manual's reset steps merits service.
Verified model details
Black 24-inch built-in dishwasher with five programs and eleven touchpads.
Source for this detailThe GSD5200 chart gives China/Crystal a 36-minute cycle.
Source for this detail · Source page: 4Beeping Clean or Normal flashes require a different response from ordinary Start/Reset drainage.
Source for this detail · Source page: 6
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE® Built-In DIshwasher - GSD5200GBB - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.