MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: Frigidaire FLVE752CBW
FLVE752CBW is a white Frigidaire electric vented dryer with a seven-cubic-foot drum, moisture sensing and three documented display faults.
Identify the exact electric dryer before following the shared guide
FLVE752CBW is the white, electric member of Frigidaire's seven-cubic-foot dryer line. Its exact specification gives a 27-inch width, 30 1/10-inch depth and 43 1/10-inch height, with a reversible door and an outdoor-vented installation. That distinguishes it from a compact ventless heat-pump appliance and matters when deciding whether an exhaust restriction could affect a load. The product page describes electronic controls with a digital readout; the exact sheet states ten cycles. Use the model plate to confirm the suffix before applying an error explanation. The linked owner's illustration explicitly covers several models, so a pictured button or program is not proof that every pictured option appears on FLVE752CBW. The exact product and its FLVE752CBW specification establish the fitted equipment.
Choose between moisture sensing and a timed cycle
The exact sheet confirms a moisture sensor, Timed Dry and programs including Active Wear, Bulky, Delicates, Heavy Duty, Normal and Sanitize. Frigidaire also advertises a 30-minute quick-dry program for this SKU. In the linked guide, sensor cycles read the load against moisture bars at the front of the drum and alter duration to reach the selected dryness. A very small or nearly dry load can escape consistent contact with those bars, causing a sensor run to stop after only a few minutes. The guide then recommends Time Dry, where you choose duration and temperature but cannot choose a sensor dryness level. This distinction is useful when a light load ends early: first identify the cycle type and load size, rather than treating the early stop as a humidity-sensor failure. Reserve the E4 interpretation for a displayed E4 code.
Separate heat, dryness and routine panel messages
FLVE752CBW offers child lock and a damp-dry signal according to its exact specification. Temperature and dryness are different settings: the exact sheet lists Low, Medium, High and Maximum under temperatures, while Max, More Dry, Normal and Less belong to dryness. Frigidaire's promotional description uses some heat labels under a 'dryness' heading, so the specification is the clearer guide to the two controls. The shared owner says that changes after a cycle has started require Pause, a new choice and Start again. It also labels Dry, Cool, Done and Clean Lint as cycle status indicators; none is one of the three fault codes. The child lock affects ordinary buttons, but the guide says Power remains available. Read the display itself before attributing a stalled selection to a failed control board.
Read the three actual fault codes without guessing a repair
Page 15 of the owner guide has a short visual error table. C9 is paired with 'PCB failed' and an instruction to call service; E5 is paired with a failed temperature sensor and the same service direction. E4 refers to the humidity sensor, but its advice differs: the current cycle can finish and manual cycles can still operate. If E4 recurs, the guide says to seek service. These are codes actually drawn in the PDF table, even though the code glyphs are absent from the PDF's extracted text layer. Record the characters as shown before contacting support. A normal Clean Lint light or an unexpectedly brief sensor cycle is not E4. The table names affected systems, not a safe owner procedure for replacing electronic parts, so avoid choosing a component from the code alone.
Check airflow and supply when drying is slow or heat is missing
Slow drying and no heat deserve checks separate from C9, E4 or E5. The exact product is vented; the linked guide calls for clearing the lint filter after every load and checking the outdoor exhaust opening. It notes that dryer-sheet residue can coat both the filter and moisture bars. For an average wet load, its loading guidance is about one third to one half of the drum, leaving room to tumble. The troubleshooting table says an electric dryer may rotate without heating if one of its two supply circuits is lost; it also lists restricted ducts and clogged outdoor hoods when cycles run long. Those observations guide the conversation with a qualified technician and help distinguish airflow or supply from a displayed sensor code. The specification's 2.27 kWh per cycle is a rated datum, not a promise for every load.
Verified model details
Exact model: 7 cu. ft., 27 inches wide, vented and fitted with a reversible door.
Source for this detailThe owner table identifies C9, E4 and E5; E4 has different interim guidance.
Source for this detail · Source page: 15The exact specification and shared owner guide distinguish fitted cycles from illustrative controls.
Source for this detail · Source page: 9
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
Frigidaire 7 Cu. Ft. Electric Dryer — FLVE752CBW
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.